TOP CATEGORIES
SPECIAL OFFER
OXYCONTROL liquid for Boiler Feed Water 30 Ltr/hr
DESCRIPTION
OXYCONTROL is a liquid catalyst compound which
reacts instantly with dissolved Oxygen in water thus
protecting the boiler from Oxygen corrosion. The highly
efficient results achieved, are based on its reaction
time and its ability to bind, to absorb and to counteract
the dissolved Oxygen, even at low temperatures.
Additionally, OXYCONTROL is applicable to all steam
generating and water systems, when the neutralizing
of dissolved carbon dioxide is required.
ADVANTAGES AND CHARACTERISTICS
6 Protects against Oxygen corrosion and can be used
at low temperatures.
6 Very efficient and rapid Oxygen scavenger.
6 Can be used in combination with a number of other
treatment products.
6 Safe to use on any steam generators and steam
boilers experiencing dissolved Oxygen saturation.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
OXYCONTROL is a concentrated liquid sulfite compound
with a specialized catalyst for Oxygen binding.
Appearance/Color : Clear, colorless liquid
Odor : Odorless
Specific gravity : 1.08–1.10 gr/cm3 at 20°C
pH value : 9.0–10.0
PACKAGING
Order Number : 673008 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
Initially, a volume of 1.2litres per ton of the boiler’s water
must be used for a period of 48 hours. Thereafter, a
dose of 300ml per ton of make-up water is sufficient to
use on a daily basis. However, daily test results should
be taken into account prior to regulating treatment.
B. Sampling and Testing
To achieve optimal results, it is important to adjust the
treated water and maintain boiler conditions by test-
ing water samples on a daily basis or at the very least,
every three days with the MARICHEM WT SULFI TEST
KIT, depending on the adjustment period to maintain
stable sulfite concentrations in the boiler’s water.
The water samples must always be taken from the
same location, as provided from the boiler manufac-
turer. Sound practice suggests sample to be cooled
via a sample cooler. Thereafter, the results may be
evaluated according to the OXYCONTROL TESTING
CHART found below.
C. Feeding Procedure
OXYCONTROL must be fed into the boiler’s feed pump
suction line or into the hot well tank, continuously, by
means of a metering pump. Other conventional ways
may also be used. However, direct feeding to the boiler
is strongly not recommended.
OXYCONTROL TM
OXYCONTROL TESTING CHART
Boiler Pressure OXYCONTROL Range in ppm as Sulfite ions
0–450 PSI 0–20 20–30 30 and over
450–850 PSI 0–10 10–15 15 and over
Results Increase Dosage 25% Satisfactory Daily Rate Decrease Dosage 25%
B.W.T. NEW FORMULA for Boiler Feed Water 30 Ltr/hr
DESCRIPTION
B.W.T. NEW FORMULA is an innovative product applied
to all types of boiler systems for water treatment. It
provides excess protection from the hard salts, sludge
concentration and corrosion, whilst also remov-
ing dissolved Oxygen (even at low temperatures).
Furthermore, it acts as an antifoam agent.
ADVANTAGES AND CHARACTERISTICS
One product does it all: a multi–functional completed
treatment.
6 Prevents Calcium corrosion through hard-
ness control.
6 Acts as an Oxygen scavenger in boiler water as well
as a corrosion inhibitor by passivating metal sur-
faces in the boiler.
6 Raises the pH level.
6 Acts as an antifoam agent.
6 Submerges suspended solids thus assisting to easy
and sufficient blowdown.
6 Should be used in conjuction with MARICHEM C.C.I.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
B.W.T. NEW FORMULA is a liquid solution of alkaline
compounds, Oxygen binders, corrosion inhibitors,
sludge conditioners and antifoam agents.
Appearance/Color : White liquid
Specific gravity : 1.15–1.20 gr/cm3 at 20°C
pH value range : 12.5–13.5
Odor : Odorless
PACKAGING
Order Number : 673003 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
Initially, use 1litre of B.W.T. NEW FORMULA per ton of
boiler water. Thereafter, a volume of 50–60ml per ton
of boiler water should be used daily.
For optimum results, consult the MARICHEM Ship’s BWT
Log Book for boiler water treatment on a daily basis.
Note that the boiler water sample analyses must be
conducted daily by using the MARICHEM WT ALKA, WT
PHOSP and WT SULFI TEST KITS.
Daily test results should be taken into account prior
to regulating treatment by either additional chemical
dosage or surface blowdown.
B. Feeding Procedure
Once the dosing quantity is determined, B.W.T. NEW
FORMULA must be introduced to the boiler’s water,
continuously, by a metering pump or by a more con-
ventional method such as metallic container, plastic
pail, etc.
DESCALER LIQUID Boiler De-Scaling 30Ltr/Drum
DESCRIPTION
DESCALER LIQUID 555 is a superior, heavy duty, con-
centrated liquid acid solution specifically designed to
remove rust and water scale build–up from boilers,
evaporators, heat exchangers, cooling systems, pipe-
line collection systems, etc.
DESCALER LIQUID 555 is characterized by the composi-
tion of high quality raw materials and the quick and
effective results once applied.
ADVANTAGES AND CHARACTERISTICS
6 Ideal for the complete removal of scale and rust
accumulation.
6 Acts quickly and thoroughly without the necessity
for heating.
6 Applicable to all ferrous metal surfaces and parts,
except stainless steel surfaces, those being gal-
vanized and those made of Tin, Zinc, Lead and
Aluminum.
6 Water–soluble, non-flammable and non-volatile.
6 Has no known effect on rubber and plastic.
6 May be combined with a specific range of
other products.
6 Can be used for difficult cleaning conditions such
as the lavatories, showers, biological wastewater
treatment units etc.
6 Cost effective, easy to apply and use.
` According to MARPOL 73/78 chemical tankers are only
permitted to use tank cleaning agents, which had
been approved and evaluated by the International
Maritime Organisation (IMO).
` DESCALER LIQUID 555 was evaluated in accordance
with MEPC.1/Circ. 590 through IMO’s Working Group
on the Evaluation of Safety and Pollution Hazards
of Chemicals (ESPH Working Group) and found to
meet the requirements of regulation 13.5.2 of Annex
II of MARPOL 73/78.
` DESCALER LIQUID 555 is not harmful to the marine
environment as per MARPOL MEPC 63 Annex
V Amendment [MEPC. 71/17/Add.1 Annex 21,
Resolution MEPC 295 (71)].
PHYSICAL PROPERTIES
DESCALER LIQUID 555 is a concentrated, non–volatile,
acid based, aqueous solution consisting of wetting
agents, corrosion inhibitors, powerful descalers and a
color indicator.
Appearance/Color : Clear, red liquid
Specific gravity : 1.15 - 1.17 gr/cm3 at 20°C
Solubility in water : Appreciable
pH value (1% Solution) : 0.5 - 2.0
Odor : Pungent
PACKAGING
Order Number : 833009 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
DESCALER LIQUID 555 must be used diluted at a pro-
portion of 1 litre for every 4–9 litres of water. Dilution
must not exceed this proportion as it may alter the
inhibiting effect of the solution.
X Note that after the application of DESCALER LIQUID
555, a 1% solution of ALKALINITY CONTROL must be
used to neutralize the treated surface area.
B. Cleaning Procedure
Preparation: Before the application of DESCALER
LIQUID 555, remove Tin, Zinc, Aluminum, Lead and
galvanized parts/components from the surface area
to be treated. Additionally, rinsing of the contaminated
area is suggested in order to eliminate sludge and
other loose deposits.
Application: DESCALER LIQUID 555 may be used
either at room temperature, or in order to accomplish
quicker results, it can be heated up, but the tempera-
ture must be no more than 55°C.
The methods used are the circulation, soaking and
spreading.
Circulation is applicable to boilers, evaporators, con-
densers, heat exchangers and generally closed sys-
tems that have the capability to circulate at a tempera-
ture of approximately 45–55°C, for 6–15 hours with a
solution of 8–12% of DESCALER LIQUID 555 in water.
Keep in mind that the strength of the solution is analo-
gous to the degree of contamination/accumulation.
BWT Formula 25 ltr/Drum Boiler Feed Water Chemical
B.W.T. POWDER is the equivalent powder product of
B.W.T. NEW FORMULA.
It is applied to all types of boiler water systems, pro-
providing excess protection from the hard salts, sludge
concentration and corrosion. Moreover, this compe-
tent product removes dissolved Oxygen and acts as
an antifoaming agent.
ADVANTAGES AND CHARACTERISTICS
6 One product does it all: a multi–functional complete
treatment.
6 Prevents salt corrosion through hardness control.
6 Acts as an Oxygen scavenger in boiler water.
6 Raises the pH level.
6 Acts as a corrosion inhibitor.
6 Acts as an antifoaming agent.
6 Submerges suspended solids thus assisting to easy
and sufficient blow down.
6 Efficiently protects boiler surfaces.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
B.W.T. POWDER is a dry powder product consisting of
alkaline compounds, Oxygen binder, corrosion inhibi-
tors, sludge conditioners and antifoam agents.
Appearance/Color : White, dry powder
Specific gravity : 1.14–1.18 gr/cm3 at 20°C
pH value (1% solution) : 12.5–13.0
Odor : Odorless
PACKAGING
Order Number : 672503 (25 kgrs)
Container : Steel drum
APPLICATION AND USE
A. Dosing Procedure
Initially, use 200grs of B.W.T. POWDER per ton of water.
Thereafter, a regulated portion of a concentrated solu-
tion must be introduced daily or at least every 2 days,
depending on the results of the relevant tests.
For optimum results, consult the MARICHEM Ship’s
BWT Log Book for boiler water treatment on a daily
basis. Always remember that the desired quantity of
B.W.T. POWDER should be dissolved in 1:10 proportion
with hot water before applying to the hot well tank.
Note that the boiler water sample analyses must be
conducted daily by using the MARICHEM WT ALKA, WT
PHOSP and WT SULFI TEST KITS.
B. Feeding Procedure
Once the desired quantity of B.W.T. POWDER is deter-
mined, dissolve the powder as described above and
feed the solution to the boiler’s water through the hot
well tank by means of a metering pump or a more
conventional method, such as a metallic container,
plastic pail, etc.
Alkaliniti controll 30 Ltr Drum
Alkaliniti controll 25 Ltr Drum
MOST POPULAR
Cum cubilia ac fringilla lorem
quis himenaeos velit.
quis himenaeos velit.
FOR TRAVELERS
OXYCONTROL liquid for Boiler Feed Water 30 Ltr/hr
DESCRIPTION
OXYCONTROL is a liquid catalyst compound which
reacts instantly with dissolved Oxygen in water thus
protecting the boiler from Oxygen corrosion. The highly
efficient results achieved, are based on its reaction
time and its ability to bind, to absorb and to counteract
the dissolved Oxygen, even at low temperatures.
Additionally, OXYCONTROL is applicable to all steam
generating and water systems, when the neutralizing
of dissolved carbon dioxide is required.
ADVANTAGES AND CHARACTERISTICS
6 Protects against Oxygen corrosion and can be used
at low temperatures.
6 Very efficient and rapid Oxygen scavenger.
6 Can be used in combination with a number of other
treatment products.
6 Safe to use on any steam generators and steam
boilers experiencing dissolved Oxygen saturation.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
OXYCONTROL is a concentrated liquid sulfite compound
with a specialized catalyst for Oxygen binding.
Appearance/Color : Clear, colorless liquid
Odor : Odorless
Specific gravity : 1.08–1.10 gr/cm3 at 20°C
pH value : 9.0–10.0
PACKAGING
Order Number : 673008 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
Initially, a volume of 1.2litres per ton of the boiler’s water
must be used for a period of 48 hours. Thereafter, a
dose of 300ml per ton of make-up water is sufficient to
use on a daily basis. However, daily test results should
be taken into account prior to regulating treatment.
B. Sampling and Testing
To achieve optimal results, it is important to adjust the
treated water and maintain boiler conditions by test-
ing water samples on a daily basis or at the very least,
every three days with the MARICHEM WT SULFI TEST
KIT, depending on the adjustment period to maintain
stable sulfite concentrations in the boiler’s water.
The water samples must always be taken from the
same location, as provided from the boiler manufac-
turer. Sound practice suggests sample to be cooled
via a sample cooler. Thereafter, the results may be
evaluated according to the OXYCONTROL TESTING
CHART found below.
C. Feeding Procedure
OXYCONTROL must be fed into the boiler’s feed pump
suction line or into the hot well tank, continuously, by
means of a metering pump. Other conventional ways
may also be used. However, direct feeding to the boiler
is strongly not recommended.
OXYCONTROL TM
OXYCONTROL TESTING CHART
Boiler Pressure OXYCONTROL Range in ppm as Sulfite ions
0–450 PSI 0–20 20–30 30 and over
450–850 PSI 0–10 10–15 15 and over
Results Increase Dosage 25% Satisfactory Daily Rate Decrease Dosage 25%
B.W.T. NEW FORMULA for Boiler Feed Water 30 Ltr/hr
DESCRIPTION
B.W.T. NEW FORMULA is an innovative product applied
to all types of boiler systems for water treatment. It
provides excess protection from the hard salts, sludge
concentration and corrosion, whilst also remov-
ing dissolved Oxygen (even at low temperatures).
Furthermore, it acts as an antifoam agent.
ADVANTAGES AND CHARACTERISTICS
One product does it all: a multi–functional completed
treatment.
6 Prevents Calcium corrosion through hard-
ness control.
6 Acts as an Oxygen scavenger in boiler water as well
as a corrosion inhibitor by passivating metal sur-
faces in the boiler.
6 Raises the pH level.
6 Acts as an antifoam agent.
6 Submerges suspended solids thus assisting to easy
and sufficient blowdown.
6 Should be used in conjuction with MARICHEM C.C.I.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
B.W.T. NEW FORMULA is a liquid solution of alkaline
compounds, Oxygen binders, corrosion inhibitors,
sludge conditioners and antifoam agents.
Appearance/Color : White liquid
Specific gravity : 1.15–1.20 gr/cm3 at 20°C
pH value range : 12.5–13.5
Odor : Odorless
PACKAGING
Order Number : 673003 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
Initially, use 1litre of B.W.T. NEW FORMULA per ton of
boiler water. Thereafter, a volume of 50–60ml per ton
of boiler water should be used daily.
For optimum results, consult the MARICHEM Ship’s BWT
Log Book for boiler water treatment on a daily basis.
Note that the boiler water sample analyses must be
conducted daily by using the MARICHEM WT ALKA, WT
PHOSP and WT SULFI TEST KITS.
Daily test results should be taken into account prior
to regulating treatment by either additional chemical
dosage or surface blowdown.
B. Feeding Procedure
Once the dosing quantity is determined, B.W.T. NEW
FORMULA must be introduced to the boiler’s water,
continuously, by a metering pump or by a more con-
ventional method such as metallic container, plastic
pail, etc.
DESCALER LIQUID Boiler De-Scaling 30Ltr/Drum
DESCRIPTION
DESCALER LIQUID 555 is a superior, heavy duty, con-
centrated liquid acid solution specifically designed to
remove rust and water scale build–up from boilers,
evaporators, heat exchangers, cooling systems, pipe-
line collection systems, etc.
DESCALER LIQUID 555 is characterized by the composi-
tion of high quality raw materials and the quick and
effective results once applied.
ADVANTAGES AND CHARACTERISTICS
6 Ideal for the complete removal of scale and rust
accumulation.
6 Acts quickly and thoroughly without the necessity
for heating.
6 Applicable to all ferrous metal surfaces and parts,
except stainless steel surfaces, those being gal-
vanized and those made of Tin, Zinc, Lead and
Aluminum.
6 Water–soluble, non-flammable and non-volatile.
6 Has no known effect on rubber and plastic.
6 May be combined with a specific range of
other products.
6 Can be used for difficult cleaning conditions such
as the lavatories, showers, biological wastewater
treatment units etc.
6 Cost effective, easy to apply and use.
` According to MARPOL 73/78 chemical tankers are only
permitted to use tank cleaning agents, which had
been approved and evaluated by the International
Maritime Organisation (IMO).
` DESCALER LIQUID 555 was evaluated in accordance
with MEPC.1/Circ. 590 through IMO’s Working Group
on the Evaluation of Safety and Pollution Hazards
of Chemicals (ESPH Working Group) and found to
meet the requirements of regulation 13.5.2 of Annex
II of MARPOL 73/78.
` DESCALER LIQUID 555 is not harmful to the marine
environment as per MARPOL MEPC 63 Annex
V Amendment [MEPC. 71/17/Add.1 Annex 21,
Resolution MEPC 295 (71)].
PHYSICAL PROPERTIES
DESCALER LIQUID 555 is a concentrated, non–volatile,
acid based, aqueous solution consisting of wetting
agents, corrosion inhibitors, powerful descalers and a
color indicator.
Appearance/Color : Clear, red liquid
Specific gravity : 1.15 - 1.17 gr/cm3 at 20°C
Solubility in water : Appreciable
pH value (1% Solution) : 0.5 - 2.0
Odor : Pungent
PACKAGING
Order Number : 833009 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
DESCALER LIQUID 555 must be used diluted at a pro-
portion of 1 litre for every 4–9 litres of water. Dilution
must not exceed this proportion as it may alter the
inhibiting effect of the solution.
X Note that after the application of DESCALER LIQUID
555, a 1% solution of ALKALINITY CONTROL must be
used to neutralize the treated surface area.
B. Cleaning Procedure
Preparation: Before the application of DESCALER
LIQUID 555, remove Tin, Zinc, Aluminum, Lead and
galvanized parts/components from the surface area
to be treated. Additionally, rinsing of the contaminated
area is suggested in order to eliminate sludge and
other loose deposits.
Application: DESCALER LIQUID 555 may be used
either at room temperature, or in order to accomplish
quicker results, it can be heated up, but the tempera-
ture must be no more than 55°C.
The methods used are the circulation, soaking and
spreading.
Circulation is applicable to boilers, evaporators, con-
densers, heat exchangers and generally closed sys-
tems that have the capability to circulate at a tempera-
ture of approximately 45–55°C, for 6–15 hours with a
solution of 8–12% of DESCALER LIQUID 555 in water.
Keep in mind that the strength of the solution is analo-
gous to the degree of contamination/accumulation.
BWT Formula 25 ltr/Drum Boiler Feed Water Chemical
B.W.T. POWDER is the equivalent powder product of
B.W.T. NEW FORMULA.
It is applied to all types of boiler water systems, pro-
providing excess protection from the hard salts, sludge
concentration and corrosion. Moreover, this compe-
tent product removes dissolved Oxygen and acts as
an antifoaming agent.
ADVANTAGES AND CHARACTERISTICS
6 One product does it all: a multi–functional complete
treatment.
6 Prevents salt corrosion through hardness control.
6 Acts as an Oxygen scavenger in boiler water.
6 Raises the pH level.
6 Acts as a corrosion inhibitor.
6 Acts as an antifoaming agent.
6 Submerges suspended solids thus assisting to easy
and sufficient blow down.
6 Efficiently protects boiler surfaces.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
B.W.T. POWDER is a dry powder product consisting of
alkaline compounds, Oxygen binder, corrosion inhibi-
tors, sludge conditioners and antifoam agents.
Appearance/Color : White, dry powder
Specific gravity : 1.14–1.18 gr/cm3 at 20°C
pH value (1% solution) : 12.5–13.0
Odor : Odorless
PACKAGING
Order Number : 672503 (25 kgrs)
Container : Steel drum
APPLICATION AND USE
A. Dosing Procedure
Initially, use 200grs of B.W.T. POWDER per ton of water.
Thereafter, a regulated portion of a concentrated solu-
tion must be introduced daily or at least every 2 days,
depending on the results of the relevant tests.
For optimum results, consult the MARICHEM Ship’s
BWT Log Book for boiler water treatment on a daily
basis. Always remember that the desired quantity of
B.W.T. POWDER should be dissolved in 1:10 proportion
with hot water before applying to the hot well tank.
Note that the boiler water sample analyses must be
conducted daily by using the MARICHEM WT ALKA, WT
PHOSP and WT SULFI TEST KITS.
B. Feeding Procedure
Once the desired quantity of B.W.T. POWDER is deter-
mined, dissolve the powder as described above and
feed the solution to the boiler’s water through the hot
well tank by means of a metering pump or a more
conventional method, such as a metallic container,
plastic pail, etc.
Alkaliniti controll 30 Ltr Drum
Alkaliniti controll 25 Ltr Drum
FAVORITE GARDEN
Many desktop publishing and
web page editors now.
web page editors now.
ALL FOR GARDEN
FURNITURE CATEGORIES
SPECIAL OFFER
2400mm crescent former facial tissue machine 14gsm@6tpd
Large 2400mm crescent former facial tissue paper making machine, paper straw making machines, home paper recycling project
Product Category : Tissue Paper Machine
Technical data:
1.Output paper:toilet paper,tissue paper.
2.Output weight:13-40g/m2
3.Net paper width: 2400mm
4.Wire width:2850mm
5.Capacity: 7-8t/d
6.Working speed:100-180m/min
7.Rail gauge:3500mm
8.Drive way:AC frequency converter and adjustable speed, drive part by part.
1.cylinder section:
Ф1500mm stainless steel cylinder mould 1set
2.couch roll section:
Size of couch roll isФ450mm,material of roll body is seamless steel pipe.
Thickness is 14mm . roll surface is coated by rubber,rubber
hardness HSD 38℃±2.
3.frame:
Frame of cylinder section is welded with shaped steel.thickness is 10mm.
4.washing device of cylinder section:
Pulp-spraying Pressure former adapt water pressing type.spray pipe DG32 stainless steel .ceramics hard wearing nozzle .
5.felt washing section:
High pressure cleaning device 2 sets
6.vacuum suction box :2set in all
7.body frame:
body frame is iron casting.material is HT200.
8.dryer cylinder :
Dryer cylinder Φ 2500mmbearing type dryer cylinder.
9.scraper of dryer cylinder:
Scraper of dryer cylinder is pneumatic,include air control chest, air cylinder.
10.touch roll:
Touch roll Φ 550 ,roll body(iron casting)surface rubber coating thickness is 25mm,shore hardness is 93°, pneumatic pressurizing ,include tyre, aircontrol chest but not contains air pump. equipped with 113632bearing.fluted rolls.
11. sink roll:
Φ194 seamless steel pipe
12. spreader roll:
Φ230 rubber coating of the surface ,rubber coating thickness is 15mm,shore hardness 93±2℃,equipped with bearing 3612.
13. exhaust hood of dryer cylinder:
Exhaust hood of the dryer can is type of respiration. include blowing fan、draft fan、radiator.
14. This machine is equipped with electromotion blanket tightening implement.pneumatic adjusting blanket implement.
15. Winding part:
sweat cylinder Φ900,equipped with bearing(113520 )
3SSB Forming Fabrics Tissue U$85/SQM
Consequat a scelerisque suspendisse vel et eget eu vitae adipiscing nibh scelerisque semper cum adipiscing facilisis adipiscing est accumsan lorem vestibulum. Aliquet mus a aptent ullam corper metus accumsan. Habitasse a purus nec ipsum a urna ac ullamcorper varius metus blandit posuere.
A4 paper making machine 100tpd @80gsm WW:3200mm for sale
A4 paper is defined by the ISO 216 standard of the International Organization for Standardization; its specification is 21 cm × 29.7 cm. A4 paper machine is suitable for office paper, printing and copying paper, and supports different weights per unit area and production capacities.
TEC-NAF is a professional supplier of paper machine equipment, specializing in the research and production of paper machines. Our product includes pulp mill machinery, spare parts, and paper production lines, such as printing paper machines, packaging paper machines, and special paper machines.
Alkaliniti controll 30 Ltr Drum
Alkaliniti controll 25 Ltr Drum
B.W.T. NEW FORMULA for Boiler Feed Water 30 Ltr/hr
DESCRIPTION
B.W.T. NEW FORMULA is an innovative product applied
to all types of boiler systems for water treatment. It
provides excess protection from the hard salts, sludge
concentration and corrosion, whilst also remov-
ing dissolved Oxygen (even at low temperatures).
Furthermore, it acts as an antifoam agent.
ADVANTAGES AND CHARACTERISTICS
One product does it all: a multi–functional completed
treatment.
6 Prevents Calcium corrosion through hard-
ness control.
6 Acts as an Oxygen scavenger in boiler water as well
as a corrosion inhibitor by passivating metal sur-
faces in the boiler.
6 Raises the pH level.
6 Acts as an antifoam agent.
6 Submerges suspended solids thus assisting to easy
and sufficient blowdown.
6 Should be used in conjuction with MARICHEM C.C.I.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
B.W.T. NEW FORMULA is a liquid solution of alkaline
compounds, Oxygen binders, corrosion inhibitors,
sludge conditioners and antifoam agents.
Appearance/Color : White liquid
Specific gravity : 1.15–1.20 gr/cm3 at 20°C
pH value range : 12.5–13.5
Odor : Odorless
PACKAGING
Order Number : 673003 (30 ltrs)
Container : Plastic jerrican
APPLICATION AND USE
A. Dosing Procedure
Initially, use 1litre of B.W.T. NEW FORMULA per ton of
boiler water. Thereafter, a volume of 50–60ml per ton
of boiler water should be used daily.
For optimum results, consult the MARICHEM Ship’s BWT
Log Book for boiler water treatment on a daily basis.
Note that the boiler water sample analyses must be
conducted daily by using the MARICHEM WT ALKA, WT
PHOSP and WT SULFI TEST KITS.
Daily test results should be taken into account prior
to regulating treatment by either additional chemical
dosage or surface blowdown.
B. Feeding Procedure
Once the dosing quantity is determined, B.W.T. NEW
FORMULA must be introduced to the boiler’s water,
continuously, by a metering pump or by a more con-
ventional method such as metallic container, plastic
pail, etc.
BWT Formula 25 ltr/Drum Boiler Feed Water Chemical
B.W.T. POWDER is the equivalent powder product of
B.W.T. NEW FORMULA.
It is applied to all types of boiler water systems, pro-
providing excess protection from the hard salts, sludge
concentration and corrosion. Moreover, this compe-
tent product removes dissolved Oxygen and acts as
an antifoaming agent.
ADVANTAGES AND CHARACTERISTICS
6 One product does it all: a multi–functional complete
treatment.
6 Prevents salt corrosion through hardness control.
6 Acts as an Oxygen scavenger in boiler water.
6 Raises the pH level.
6 Acts as a corrosion inhibitor.
6 Acts as an antifoaming agent.
6 Submerges suspended solids thus assisting to easy
and sufficient blow down.
6 Efficiently protects boiler surfaces.
6 Cost effective, easy to handle and apply.
PHYSICAL PROPERTIES
B.W.T. POWDER is a dry powder product consisting of
alkaline compounds, Oxygen binder, corrosion inhibi-
tors, sludge conditioners and antifoam agents.
Appearance/Color : White, dry powder
Specific gravity : 1.14–1.18 gr/cm3 at 20°C
pH value (1% solution) : 12.5–13.0
Odor : Odorless
PACKAGING
Order Number : 672503 (25 kgrs)
Container : Steel drum
APPLICATION AND USE
A. Dosing Procedure
Initially, use 200grs of B.W.T. POWDER per ton of water.
Thereafter, a regulated portion of a concentrated solu-
tion must be introduced daily or at least every 2 days,
depending on the results of the relevant tests.
For optimum results, consult the MARICHEM Ship’s
BWT Log Book for boiler water treatment on a daily
basis. Always remember that the desired quantity of
B.W.T. POWDER should be dissolved in 1:10 proportion
with hot water before applying to the hot well tank.
Note that the boiler water sample analyses must be
conducted daily by using the MARICHEM WT ALKA, WT
PHOSP and WT SULFI TEST KITS.
B. Feeding Procedure
Once the desired quantity of B.W.T. POWDER is deter-
mined, dissolve the powder as described above and
feed the solution to the boiler’s water through the hot
well tank by means of a metering pump or a more
conventional method, such as a metallic container,
plastic pail, etc.
Ceramic Hydrofoil with SS Box
Consequat a scelerisque suspendisse vel et eget eu vitae adipiscing nibh scelerisque semper cum adipiscing facilisis adipiscing est accumsan lorem vestibulum.
DESCALER Boiler De scaling 25 Ltr/Drum
DESCRIPTION
DESCALER POWDER is an advanced acid concentrated
dry powder formula consisting of a blend of specific
acids, wetting agents, corrosion inhibitors, antifoam
agents and a color indicator. Its purpose is to remove
hard scale and rust deposits from water boilers, diesel
engine cooling systems, condensers, evaporators,
heat exchangers, pipeline collection systems, etc.
DESCALER POWDER is similar to DESCALER LIQUID 555
as to its properties and range of applications. However,
the difference lies over the fact that DESCALER POWDER
is a dry powder formula, which makes it easy and
safe to handle and store in awkward conditions.
Furthermore, DESCALER POWDER is safe to use on
sensitive metals and their alloys such as Zinc, Lead,
Aluminum, Tin etc.
ADVANTAGES AND CHARACTERISTICS
6 Highly effective for the complete removal of rust
and scale deposits from water boilers, engine cool-
ing systems and other water processing units and
installations, due to its wetting agents.
6 Acts quickly and thoroughly.
6 Requires no heating unless its activity is required to
increase drastically.
6 Due to its strong corrosion inhibitors, it is applicable
to all ferrous metal surfaces and parts, as well as
those being galvanized and those made of Tin, Zinc,
Lead, Aluminum etc.
6 Contains anti–foaming agents and a color indicator
as a determinant agent of the strength of the powder.
6 Water–soluble, non-flammable, non-volatile and
non-hydroscopic.
6 Has no known effect on rubber and plastic
compounds.
6 May be combined with a specific range of
other products.
6 Can be used for difficult cleaning conditions such
as the lavatories, showers, biological wastewater
treatment units etc.
6 Cost effective, easy to handle, apply and store.
` DESCALER POWDER is not harmful to the marine
environment as per MARPOL MEPC 63 Annex
V Amendment [MEPC. 71/17/Add.1 Annex 21,
Resolution MEPC 295 (71)].
PHYSICAL PROPERTIES
DESCALER POWDER is a concentrated, highly acidic
powder compound containing a blend of strong acids,
wetting agents, corrosion inhibitors, anti–foam agents
and a color acid indicator.
Appearance/Color : Reddish powder
Specific gravity : 1.3 - 1.4 gr/cm3 at 20°C
Solubility : Moderate, slow reaction
pH value (10% Solution) : 1.0 - 2.0
Odor : Odorless
PACKAGING
Order Number : 832509 (25 kgrs)
Container : Steel drum
APPLICATION AND USE
A. Dosing Procedure
The quantity of DESCALER POWDER to be used cor-
responds to the scale and degree of contamination,
the available downtime, the desired results and the
system to be treated. Therefore, the concentration of
the applied solution must be made after considering
the above parameters. However, DESCALER POWDER
is recommended for use at a quantity proportion of
4–5kgs for every 100litres of fresh water.
B. Preparation
There are certain actions, which must be taken before
applying DESCALER POWDER. These are the following:
Dissolve the powder in fresh water at a concentra-
tion of 4–5%.
Before the application of the solution, rinse the area to
be treated thoroughly with water in order to eliminate
sludge and other loose deposits
C. Cleaning Procedure
DESCALER POWDER may be used either at room tem-
perature or can be heated up to no more than 60 oC
in order to increase its activity and reduce the reac-
tion rate.
The methods to use are circulation, soaking and
spreading.
Circulation is applicable to boilers, evaporators, con-
densers, heat exchangers and generally closed sys-
tems that have the capability to circulate at a tempera-
ture of approximately 45–60°C, for 6–15 hours.












